Factory default cisco catalyst switch configuration

images factory default cisco catalyst switch configuration

Forgot Password No problem! In this case, you need to follow the password recovery procedures for your switch. You can then delete the config file, or rename it, also rename or delete the vlan. Contents Introduction. I may unsubscribe at any time. Your password has been sent to: cguarrera techtarget. If you have configured a switch and the configuration has become very complex or if you want to move a switch from one network to other, you can reset the switch to factory defaults and configure it as a new switch. Once you clear the user configuration, there is no way to recover the configuration unless you restore the backed-up configuration. To reset the switch to factory default, issue the erase startup-config or write erase command. We'll let you know when a new response is added.

  • How to Reset a Cisco Catalyst / Switch to Factory Defaults Simplified Voice
  • How to reset the Cisco Catalyst Switch to Factory Defaults Network technologies and trends
  • Resetting Catalyst Switches to Factory Defaults Cisco

  • How to Reset a Cisco Catalyst / Switch to Factory Defaults Simplified Voice

    To reset the switch to factory default, issue the erase startup-config or write erase command. This command does not. Do not save the configuration at this prompt.

    Otherwise, the switch!

    How to reset the Cisco Catalyst Switch to Factory Defaults Network technologies and trends

    reloads with the current running configuration and does not reset to. then reload the switch Guys,I mean reset the switch not erase the configuration, the switch was in a stack The password-recovery mechanism is enabled.
    You can alter the boot variable settings with the set boot command.

    We'll email you when relevant content is added and updated. The information in this document was created from the devices in a specific lab environment. Sort by: Oldest Newest Sorting replies If your switch has any router cards, the clear config all command does not clear the Cisco IOS Software configuration on the router cards. Refer to this document for steps to recover the passwords on your Catalyst switches:. To reset the switch to factory default, issue the erase startup-config or write erase command.

    images factory default cisco catalyst switch configuration

    images factory default cisco catalyst switch configuration
    Factory default cisco catalyst switch configuration
    All of the devices used in this document started with a cleared default configuration.

    Working with Configuration Files.

    Video: Factory default cisco catalyst switch configuration Cisco Switch 2950/2960 Reset to Factory Defaults

    Ask a question, help others, and get answers from the community. This document provides information and sample command logs to reset your switches. I may have left out a step or two.

    You can reset the system or module configuration on these switches running CatOS to factory defaults with the clear config command.

    For XL, XL,, and series switches. You still can do password-recovery when you run that command.

    images factory default cisco catalyst switch configuration

    The following commands will initialize the flash filesystem, and finish loading the operating system software: flash_init boot switch. How to Reset a Cisco Catalyst / Switch to Factory Defaults. Enter the following commands in the privileged mode: (# prompt). delete flash:
    This command does not, however, clear the boot variables, such as config-register and boot system settings.

    Resetting Catalyst Switches to Factory Defaults Cisco

    You can then delete the config file, or rename it, also rename or delete the vlan. This is useful when you want to remove an undesirable configuration that is present in the switch. So, if you reset the configuration on the active Supervisor Engine to factory defaults with the clear config command, the standby Supervisor Engine also resets to factory defaults. To reset the VLAN information to the factory defaults, delete the vlan.

    Video: Factory default cisco catalyst switch configuration Cisco Catalyst Switch Factory Default

    Whether you set the configuration mode to binary or text mode with the set config mode command, the switch resets to factory defaults when you clear the configuration on the active Supervisor Engine.

    images factory default cisco catalyst switch configuration
    Factory default cisco catalyst switch configuration
    Welcome to TechTarget's expert community for technology professionals. To erase the vlan. The file is called vlan. Now lets issue the following commands to reset the Cisco Catalyst Switch to factory default setting:.

    Delete the vlan. In certain situations, it is desirable to restore the Catalyst switch configuration to the original default factory settings. Share this item with your network:.